Skip to main content

Electronic Governor and how it is controlling Main Engine Speed

M/E Electronic governor is an Electronic PID controller to Control the RPM of M/E precisely at the set value. It is forming part of the bridge manoeuvring system (BMS). Main parts of an electronic governor are,
Main control unit: This is the CPU based process unit which is controlling the Engine RPM. The inputs to this unit are the speed order signal from the operator, Actual RPM Signal from the Pickups and Scavenging air pressure signal from Scavenge Air receiver. The output signal from this section goes to the Servo controller.
Servo Controller: This unit receiving signal from the Control unit and giving an output voltage to the Servo Motor. This servo motor is regulating the fuel rack to maintain the set RPM by the operator. A feedback signal from a Resolver which is forming part of the actuator will be given to the servo driver to position the servo motor shaft at correct angle.
RPM Pickups: Which are sensing the real time RPM and giving to Main control unit for comparison with set value.
Pressure transducer: This pressure transducer converts the scavenge air pressure to a 4-20 mA signal and giving to Main control unit for regulating the fuel according to the combustion curve stored in the CPU

Comments

  1. Thank you so much for sharing this blog with us. It provides a collection of useful information. You obviously put a lot of effort into it! Best مشاريع التجارة الالكترونية service provider.

    ReplyDelete

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators

Why is a man hole door elliptical in shape?

Any opening in a pressure vessel is kept to a minimum and for a man entry an elliptical hole  is lesser in size than the corresponding circular hole. More over it is prime concern to have a  smoothed generous radius at the corners to eliminate stress concentration. Hence other  geometrical shapes like rectangle and square are ruled out.  To compensate for the loss of material in the shell due to opening, a doubler ring has to be  provided around the opening. The thickness of the ring depends on the axis length along the  dirrection in which the stresses are maximum and the thickness of the shell. It is important to  align the minor axis along the length of the vessel, as the stress in this direction is  maximum. Longitudinal stress: Pd/2t where P= pressure inside the vessel, d= diameter of the arc, t=  thickness of the shell plating  Circumferential stress: Pd/4t  More over a considerable material and weight saving is achieved as minor is along the  direction of maximum stress.

Shell Expansion Plan

It is a two dimensional drawing of a three dimensional surface of the ship’s hull form. This plan is very useful for the following information:It is used for marking the location of a hull Damage on this plan by identifying the strake number , letter and frame number so that the exact location of the damage and also suggested repairs are marked in a localised copy. The shell expansion can be used for finding areas of painting surfaces such as topside, boot topping and bottom areas by applying Simpsons rules directly.  In the shell expansion the vertical scale used is different from the horizontal scale and a suitable adjustment has to be made when calculating areas. This becomes useful in solving disputes concerning areas of preparation and painting. It gives information on the thickness of the original strake which is indicated by the number in the circle shown in the strake.  The quality of steel used is also shown by letters A,B,D E and AH, BH,DH, EH.