Skip to main content

Explain the various rudder inspections and testing in the dry dock

a. Visual examination of the rudder plating for cracks and distortion 
b. Air plugs and drain plugs are to be opened in the presence of the class surveyor, 
repair superintendent and chief officer. Water draining out indicates a breached 
rudder and the breach to be located by air pressure testing and applying soap 
solution, repairs to be planned 
c. Check the rudder drop in the steering gear compartment (trammel gauge) 
d. Check the pintle clearances, jumping bar clearance and the palm coupling bolts 
tightness to be checked 
e. Check the rudder stock for corrosion, erosion and any damage 
f. The inspection plates in the way of the upper, the lower pintle to be cut open, and the 
pintle nuts checked for proper securing. Later the plates to be welded and tested. 
g. Hydraulic test the rudder for a static head of about 2.45m of sea water 
h. After draining and re oiling the internals, plug the drain and check the effectiveness 
by a vacuum check and cement the plug 
i. The rudder stock gland packing has to be checked and renewed

Comments

  1. goinspectSeptember 8, 2022 at 2:08 AM

    I got some valuable points through this blog. Thank you sharing this blog.
    Handover Inspection Brisbane

    ReplyDelete

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation...
8 comments
Read more

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators
15 comments
Read more

Manganese bronze is not typically used as a propeller material .Why

1. High cost: Manganese bronze is a costly alloy, making it less economical for large propellers. 2. Low strength-to-weight ratio: Compared to other propeller materials like nickel-aluminum bronze or stainless steel, manganese bronze has a lower strength-to-weight ratio. 3. Susceptible to corrosion: Manganese bronze can corrode in seawater, especially when exposed to high velocities and turbulence. 4. Poor cavitation resistance: Manganese bronze is more prone to cavitation damage than other materials. 5. Difficult to cast and machine: Manganese bronze is challenging to cast and machine, making it less desirable for complex propeller geometries. 6. Limited weldability: Manganese bronze has poor weldability, making repairs and modifications difficult. Nickel-aluminum bronze or stainless steel are commonly used for propellers due to their: - High strength and durability - Excellent corrosion resistance - Good cavitation resistance - Ease of casting and machining - Weldability
88 comments
Read more