Skip to main content

Miller cycle and emission reduction

The Miller cycle was developed by Ralph Miller in the 1940s. With the introduction of turbocharging to the 4 stroke diesel engines, the Mean Effective Pressure and thus the power output of 4 stroke engines rose by 50 - 60%. However this was about the limit; If the  inlet air pressure was increased further, then the charge air reached excessive pressures and temperatures on compression causing burning of the LO film and thermal stressing.

Miller challenged the thinking of the day by closing the inlet valve before the piston reached bottom dead centre. This had the effect of lowering the cylinder pressure as the piston continued downwards, as well as dropping the temperature of the air (Boyles and Charles' Law). Although the engine is still doing work as the piston is descending on the inlet stroke, there is a saving in work during the compression stroke, and the maximum air temperature and pressure is reduced on compression. The timing of the inlet valve of  Miller's engine was governed by a mechanical link arrangement, and varied automatically with engine load. Miller's engine doubled the MEP of the engine when compared with a naturally aspirated engine.

Advances in design and materials led to more efficient turbochargers, higher compression ratios and more efficient cooling of marine diesel engines. However, with the introduction of MARPOL VI, manufacturers had to look more closely at lowering NOx and smoke emissions.

One of the methods used is to reintroduce the Miller cycle using variable inlet closing, so that at full load, the maximum cylinder temperature is reduced. (NOx formation occurs at temperatures in excess of 1200°C). This is combined with higher compression ratios and slightly later fuel injection timing.

Miller relied on mechanical methods to vary the timing. Modern methods linked to a computer controlled engine management system use a hydraulic push rod.


 Low load operation: The throttle valve opens against a spring as the follower moves up the cam and oil is displaced under the push rod piston, opening the valve. When the follower comes off the cam, the throttle valve is closed and oil can only flow through the throttle orifice, delaying the closing ofthe inlet valves.
At full load operation, an air signal opens the throttle valve. This means that as soon as the follower descends from the cam peak, the pushrod piston moves downwards, allowing the inlet valves toclose
In this second method of control, the Variable Inlet Closing consists of two hydraulic cylinders connected by two passages, the flow through one of these passages being controlled by a valve, and the other by the position of the hydraulic piston driven by the cam follower.

When the follower moves up the slope of the cam the oil in the lower cylinder moves to the upper cylinder displacing the push rod piston and opening the valves. When the follower is on the peak of the cam, the hydraulic piston is covering the passage between the  cylinders.

When the VIC control valve is open, the pushrod follows the follower immediately, which results in early valve closure. When the control valve is closed, the downward movement of the pushrod is delayed until the piston actuated by the tappet reveals the passage between the two cylinders.

Make up of oil is from the main engine Lub Oil supply via a non return valve. Build up of air is prevented by an air release in the push rod hydraulic cylinder.

By increasing the compression ratio, giving a higher air temperature the ignition delay is reduced. Later injection over a shorter period combined with improved fuel atomisation and combustion space design result in lower NOx formation.


 
TWO STROKE ENGINES
The two stroke engine cannot utilise the Miller cycle. However they can use variable exhaust valve closing; easily achieved with an electronically controlled camshaftless engine or by involving hydraulic valves as in the case of the modified Sulzer RTA


NOTE
Supercharged petrol engines also make use of a form of Miller cycle in which the inlet valve is left open during the first part of the compression stroke, so that compression only occurs during the last 70% of the compression stroke. Over the entire compression range required by the engine, the supercharger is used to generate low levels of compression, where it is most efficient. The air is then cooled in the air cooler. Then, the piston is used to generate the remaining higher levels compression, operating in the range where it is more efficient than a supercharger. Thus the Miller cycle when used in a petrol engine uses the supercharger for the portion of the compression where it is best, and the piston for the portion where it is best. In total, this reduces the power needed to run the engine by 10% to 15%.

Comments

  1. I found decent information in your article. I am impressed with how nicely you described this subject, It is a gainful article for us. Thanks for share it.Hydraulic Clamping System Manufacturers

    ReplyDelete

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators

Why is a man hole door elliptical in shape?

Any opening in a pressure vessel is kept to a minimum and for a man entry an elliptical hole  is lesser in size than the corresponding circular hole. More over it is prime concern to have a  smoothed generous radius at the corners to eliminate stress concentration. Hence other  geometrical shapes like rectangle and square are ruled out.  To compensate for the loss of material in the shell due to opening, a doubler ring has to be  provided around the opening. The thickness of the ring depends on the axis length along the  dirrection in which the stresses are maximum and the thickness of the shell. It is important to  align the minor axis along the length of the vessel, as the stress in this direction is  maximum. Longitudinal stress: Pd/2t where P= pressure inside the vessel, d= diameter of the arc, t=  thickness of the shell plating  Circumferential stress: Pd/4t  More over a considerable material and weight saving is achieved as minor is along the  direction of maximum stress.

Shell Expansion Plan

It is a two dimensional drawing of a three dimensional surface of the ship’s hull form. This plan is very useful for the following information:It is used for marking the location of a hull Damage on this plan by identifying the strake number , letter and frame number so that the exact location of the damage and also suggested repairs are marked in a localised copy. The shell expansion can be used for finding areas of painting surfaces such as topside, boot topping and bottom areas by applying Simpsons rules directly.  In the shell expansion the vertical scale used is different from the horizontal scale and a suitable adjustment has to be made when calculating areas. This becomes useful in solving disputes concerning areas of preparation and painting. It gives information on the thickness of the original strake which is indicated by the number in the circle shown in the strake.  The quality of steel used is also shown by letters A,B,D E and AH, BH,DH, EH.