Skip to main content

Procedures and precautions when cleaning both air and water sides of a charge air cooler.




Cleaning air side

On a large 2 stroke crosshead engine the air cooler may be cleaned by injecting an air cleaner chemical into the charge air while the engine is running. The chemical used is hazardous to health and thus protective clothing must be worn, and manufacturers instructions followed. Alternatively, a system using a chemical circulating tank, pump and built in sprays may be used when the engine is stopped. After circulating the chemical for a period of time as instructed, the air cooler must be rinsed using fresh water. Ensure drains from the air cooler to bilge are clear.
On a medium speed engine, the air cooler can be cleaned in situ (with the engine stopped) by blanking the air inlet and outlet and filling with a cleaning solution. However it will be necessary to support the air cooler, as the fastenings used may not be designed to cope with the extra weight. However it may be easier to remove the whole air cooler and place it in a bath of cleaning solution. Again protective clothing must be worn, and suitable ventilation provided. It is normal practise to pressure test the cooler stack when it is in the rinsing bath to check for leaking tubes.

Cleaning water side

This is normally done in situ with the engine stopped. After isolation and draining, the end covers on the cooling water boxes are removed and the cooler is rodded through or blasted using a pressure lance. In the case of the latter suitable protective clothing must be worn. Cleaning the water side is normally only carried out on air coolers using sea water. sacrificial anodes should be inspected and replaced as necessary.

It is necessary to maintain the correct charge air temperature for the following reasons:
    1.    So that the correct mass of air is allowed into the cylinder for combustion of the fuel. (the higher the temperature the greater the specific volume)
    2.    To keep the exhaust gas temperature at acceptable levels. (will rise if air temp is too high)
    3.    To prevent water depositing on the liner surface destroying L.O. film if temp is too low.
    4.    To prevent thermal shocking of liner if temp is too low.
Labels:

Comments

  1. Arjun kumarApril 10, 2023 at 6:55 AM

    Wow, This is a very nice write up for everyone. Everyone will benefit greatly from it this summer. So many thanks for such a nice informative post. desert cooler

    ReplyDelete
  2. septic serviceApril 14, 2023 at 5:11 AM

    In the metro Atlanta area, we offer a comprehensive range of septic services to customers. Our areas of expertise include septic pumping, septic cleaning, and septic repair septic tank cleaning near me

    ReplyDelete
  3. Mark PouseeAugust 8, 2025 at 12:28 AM

    Looking for peaceful sleep during summer? The best air cooler for bedroom in Pakistan should be compact, noise-free, and energy-efficient. Brands like Boss, GFC, and Orient offer bedroom-friendly models with silent operation and adjustable fan speeds.

    ReplyDelete

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation...
7 comments
Read more

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators
14 comments
Read more

Shell Expansion Plan

It is a two dimensional drawing of a three dimensional surface of the ship’s hull form. This plan is very useful for the following information:It is used for marking the location of a hull Damage on this plan by identifying the strake number , letter and frame number so that the exact location of the damage and also suggested repairs are marked in a localised copy. The shell expansion can be used for finding areas of painting surfaces such as topside, boot topping and bottom areas by applying Simpsons rules directly.  In the shell expansion the vertical scale used is different from the horizontal scale and a suitable adjustment has to be made when calculating areas. This becomes useful in solving disputes concerning areas of preparation and painting. It gives information on the thickness of the original strake which is indicated by the number in the circle shown in the strake.  The quality of steel used is also shown by letters A,B,D E and AH, BH,DH, EH.
20 comments
Read more