Skip to main content

Loadline ( Plimsoll ) Marking


Each vessel is required to hold a Loadline Certificate. Part of the requirements for this is the permanent marking of loadlines on either side of the hull arounf about midhsips. Permanent marking means that they have to be impressed or welded so that they cannot be removed by normal wear and tear. They should be white or yellow on a dark contrasting back ground. Regulations govern the number and size of these, the main ones are described below.

Danish Load mark
The Load Line Mark shall consist of a ring 300 millimeters (12 inches) in outside diameter and 25 millimeters (1 inch) wide which is intersected by a horizontal line 450 millimeters (18 inches) in length and 25 millimeters (1 inch) in breadth, the upper edge of which passes through the centre of the ring. The centre of the ring shall be placed amidships and at a distance equal to the assigned summer freeboard measured vertically below the upper edge of the deck line

Deck Mark
The deck line is a horizontal line 300 millimeters (12 inches) in length and 25 millimeters (1 inch) in breadth. It shall be marked amidships on each side of the ship, and its upper edge shall normally pass through the point where the continuation outwards of the upper surface of the freeboard deck intersects the outer surface of the shell. The location of the reference point and the identification of the freeboard deck is indicated on the International Load Line Certificate (1966). Lines to be used with the Load Line Mark

Loadline Mark
The lines which indicate the load line shall be horizontal lines 230 millimeters (9 inches) in length and 25 millimeters (1 inch) in breadth which extend forward of, unless expressly provided otherwise, and at right angles to, a vertical line 25 millimeters (1 inch) in breadth marked at a distance 540 millimeters (21 inches) forward of the centre of the ring . Aft of thevertical mark refers to loading in freshwater only. For'd refers to loading in sea water only
   
The loadline mark consists of the following marks
  • The Summer Load Line indicated by the upper edge of the line which passes through the centre of the ring and also by a line marked S.
  • The Winter Load Line indicated by the upper edge of a line marked W.
  • The Winter North Atlantic Load Line indicated by the upper edge of a line marked WNA.
  • The Tropical Load Line indicated by the upper edge of a line marked T.
  • The Fresh Water Load Line in summer indicated by the upper edge of a line marked F.
  • The Tropical Fresh Water Load Line indicated by the upper edge of a line marked TF


Labels:

Comments

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Manganese bronze is not typically used as a propeller material .Why

1. High cost: Manganese bronze is a costly alloy, making it less economical for large propellers. 2. Low strength-to-weight ratio: Compared to other propeller materials like nickel-aluminum bronze or stainless steel, manganese bronze has a lower strength-to-weight ratio. 3. Susceptible to corrosion: Manganese bronze can corrode in seawater, especially when exposed to high velocities and turbulence. 4. Poor cavitation resistance: Manganese bronze is more prone to cavitation damage than other materials. 5. Difficult to cast and machine: Manganese bronze is challenging to cast and machine, making it less desirable for complex propeller geometries. 6. Limited weldability: Manganese bronze has poor weldability, making repairs and modifications difficult. Nickel-aluminum bronze or stainless steel are commonly used for propellers due to their: - High strength and durability - Excellent corrosion resistance - Good cavitation resistance - Ease of casting and machining - Weldability
107 comments
Read more

MAN B&W MC Engine VIT Pump

The pump is basically a jerk type with a plunger moving in a matched barrel, using two helical grooves machined in the plunger to control the end of injection by uncovering spill ports and causing the discharge pressure to drop rapidly, thus causing the needle valve in the injector to close. Oil is supplied to the barrel via the spill ports and a suction valve. The suction valve, situated at the top of the barrel opens when the pressure in the  barrel falls below the supply pump pressure; i.e. during downward stroke of plunger, while spill ports are covered by plunger. Replaceable erosion plugs  are fitted in the pump housing opposite the spill ports. The high pressure oil, spilling back, as the edge of the helix uncovers the s...
Post a Comment
Read more

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation...
9 comments
Read more