Skip to main content

Drydock Stability

  • When the ship enters a dry dock, it must have a positive metacentric height; and is usually trimmed by stern. The floor of the dry dock is lined with keel blocks, which are so arranged such that they can bear the weight of the ship. When the ship enters the dry dock, her centerline is first brought in line with the centerline of the keel blocks by using a combination of plum lines and Leica theodolite.
  • The dock gates are then closed and the water is pumped out of the dock in stages. Since the ship has a trim by stern, the stern of the ship will first sit on the keel blocks. The rate of pumping out water is reduced as the stern is almost about to touch the keel blocks. The reason is, it is from this stage of the docking procedure when the stability of the ship starts getting critical. The interval of time from when the stern takes the blocks to the moment when the entire ship’s weight is borne by the blocks is called Critical Period. We will understand the details a little later.
  • When the stern of the ship takes the blocks, it is fixed to the shores (sides of the dock). This is carried out from aft to forward so that by the time the entire ship takes the blocks, it is fixed to the shores. When the ship is completely borne by the blocks, water is pumped out quickly from the dock.
  • When the ship’s stern just touches the keel blocks, part of the ship’s weight is being borne by the keel blocks. The contact between the stern and the keel block creates a normal reaction or upthrust. The magnitude of this upward normal reaction increases as the water level in the dry dock reduces. It is this upthrust that creates a virtual reduction in the metacentric height of the ship. Hence it is very crucial to maintain sufficient positive metacentric height before docking, lacking which, the ship may heel over to either side, or even slip off the keel blocks and capsize.
Three vertical parallel forces acting on the ship:
  • Weight (W) acting downward.
  • Keel block upthrust (P) acting upward.
  • Buoyancy (W-P) acting upward.
The upthrust force (P) can be considered to have an effect similar to that of removal of a weight from the ship. This has the virtual effect of rising the center of gravity of the ship from the point ‘G’ to ‘G1’. The metacentric height therefore reduces from GM to G1
H            Virtual rise in CG during dry docking.
The virtual reduction in metacentric height at any stage of the docking process can be calculated by the following expression:

  • This calculation must be carried out for the condition when the ship has just touched the keel blocks throughout its length. 
  • It is at this point that the keel block upthrust is maximum, and the risk of tipping over or slipping from keel blocks is most likely if the metacentric height is too low or negative

Labels:

Comments

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Manganese bronze is not typically used as a propeller material .Why

1. High cost: Manganese bronze is a costly alloy, making it less economical for large propellers. 2. Low strength-to-weight ratio: Compared to other propeller materials like nickel-aluminum bronze or stainless steel, manganese bronze has a lower strength-to-weight ratio. 3. Susceptible to corrosion: Manganese bronze can corrode in seawater, especially when exposed to high velocities and turbulence. 4. Poor cavitation resistance: Manganese bronze is more prone to cavitation damage than other materials. 5. Difficult to cast and machine: Manganese bronze is challenging to cast and machine, making it less desirable for complex propeller geometries. 6. Limited weldability: Manganese bronze has poor weldability, making repairs and modifications difficult. Nickel-aluminum bronze or stainless steel are commonly used for propellers due to their: - High strength and durability - Excellent corrosion resistance - Good cavitation resistance - Ease of casting and machining - Weldability
107 comments
Read more

MAN B&W MC Engine VIT Pump

The pump is basically a jerk type with a plunger moving in a matched barrel, using two helical grooves machined in the plunger to control the end of injection by uncovering spill ports and causing the discharge pressure to drop rapidly, thus causing the needle valve in the injector to close. Oil is supplied to the barrel via the spill ports and a suction valve. The suction valve, situated at the top of the barrel opens when the pressure in the  barrel falls below the supply pump pressure; i.e. during downward stroke of plunger, while spill ports are covered by plunger. Replaceable erosion plugs  are fitted in the pump housing opposite the spill ports. The high pressure oil, spilling back, as the edge of the helix uncovers the s...
Post a Comment
Read more

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation...
9 comments
Read more