Skip to main content

Types of lubrication

Hydrodynamic lubrication (full fluid film) 

(1) Moving surfaces are separated completely by the pressure of a continuous unbroken film or a  layer of lubricant, generated by the movement of the two surfaces relative to each other. 
(2) Essential requirement is formation of a wedge of lubricants between surfaces. 
(3) Thickness of film 0.025 – 0.10 mm. 
(4) Lubrication for Journal Bearing, Bottom End Bearing, Tilting Pad Thrust Bearing

Boundary lubrication 

(1) It exists when a full-fluid film lubrication is not possible. 
(2) The sliding surfaces are separated by only a thin film of lubricant. 
(3) High friction between the surfaces and some degree of metal to metal contact occurs 
(4) Lubricant oil film decreases, until asperities of mating surfaces touch 

Hydrostatic lubrication 

(1) A form of thick film lubrication, but instead of being self- generated, it is supplied from an  external source by oil under pressure from a pump. 
(2) Lubrication for Crosshead Bearings, with attached pump. 

Elasto-hydrodynamic lubrication

(1) Applies to line contact or nominal point between rolling or sliding surfaces, such as rolling  contact bearings and meshing gear teeth. 
(2) Thin film or squeeze film lubrication limits metal to metal contact. 
(3) Elastic deformation of the metals occurs, and there is effect of high pressure on the lubricant.

Comments

  1. Precision TransfersNovember 22, 2021 at 12:43 AM

    Hey what a brilliant post I have come across and believe me I have been searching out for this similar kind of post for past a week and hardly came across this. Thank you very much and will look for more postings from you Best 8MM FILM TRANSFER service provider

    ReplyDelete

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Manganese bronze is not typically used as a propeller material .Why

1. High cost: Manganese bronze is a costly alloy, making it less economical for large propellers. 2. Low strength-to-weight ratio: Compared to other propeller materials like nickel-aluminum bronze or stainless steel, manganese bronze has a lower strength-to-weight ratio. 3. Susceptible to corrosion: Manganese bronze can corrode in seawater, especially when exposed to high velocities and turbulence. 4. Poor cavitation resistance: Manganese bronze is more prone to cavitation damage than other materials. 5. Difficult to cast and machine: Manganese bronze is challenging to cast and machine, making it less desirable for complex propeller geometries. 6. Limited weldability: Manganese bronze has poor weldability, making repairs and modifications difficult. Nickel-aluminum bronze or stainless steel are commonly used for propellers due to their: - High strength and durability - Excellent corrosion resistance - Good cavitation resistance - Ease of casting and machining - Weldability
107 comments
Read more

MAN B&W MC Engine VIT Pump

The pump is basically a jerk type with a plunger moving in a matched barrel, using two helical grooves machined in the plunger to control the end of injection by uncovering spill ports and causing the discharge pressure to drop rapidly, thus causing the needle valve in the injector to close. Oil is supplied to the barrel via the spill ports and a suction valve. The suction valve, situated at the top of the barrel opens when the pressure in the  barrel falls below the supply pump pressure; i.e. during downward stroke of plunger, while spill ports are covered by plunger. Replaceable erosion plugs  are fitted in the pump housing opposite the spill ports. The high pressure oil, spilling back, as the edge of the helix uncovers the s...
Post a Comment
Read more

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation...
9 comments
Read more