Skip to main content

Advantage and Disadvantages of controllable pitch propeller

 Advantages of CPP

Improved Maneuverability.
Full ahead to astern un 12 seconds.
Lower ship speed can be obtained.
Crash stop feature.
Improved water flow into the rudder.
Full engine power available for astern movements.
Fewer engine starts.
Low thermal.load on engine.
Less engine wear.
Less stern tube bearing wear.
Lower starting air comsumption.
No requirement for reversing gear.
Higher engine efficiency
Pitch adjustable for hull fouling and different sea conditions
Engine power and speeds can be altered to stay clear of T/C surging zones


Disadvantages of CPP
Propellor heavier which will increase stress on tail shaft and stern tube bearings
Survey period reduced by 1 year
Additional cost during survey
Lower propellor efficiency due to large dia hub versus propeller diameter
Drop in efficiency range from 2 to 3 percent.
Increased risk of breakdown due to system dependence and greater chance of cavitation damage on propellor blades


Comments

  1. legacymarbleandgraniteJanuary 6, 2021 at 11:29 PM

    Nice article, which you have shared. Your article is very informative and useful. Thanks for sharing this article here. OEE Downtime Tracking

    ReplyDelete
  2. downtimecollectionsolutionsSeptember 30, 2023 at 4:42 AM

    It is a proficient article that you have shared here about OEE Tracking I got some unique and valuable information from your article. Thankful to you for sharing this article here.

    ReplyDelete

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Manganese bronze is not typically used as a propeller material .Why

1. High cost: Manganese bronze is a costly alloy, making it less economical for large propellers. 2. Low strength-to-weight ratio: Compared to other propeller materials like nickel-aluminum bronze or stainless steel, manganese bronze has a lower strength-to-weight ratio. 3. Susceptible to corrosion: Manganese bronze can corrode in seawater, especially when exposed to high velocities and turbulence. 4. Poor cavitation resistance: Manganese bronze is more prone to cavitation damage than other materials. 5. Difficult to cast and machine: Manganese bronze is challenging to cast and machine, making it less desirable for complex propeller geometries. 6. Limited weldability: Manganese bronze has poor weldability, making repairs and modifications difficult. Nickel-aluminum bronze or stainless steel are commonly used for propellers due to their: - High strength and durability - Excellent corrosion resistance - Good cavitation resistance - Ease of casting and machining - Weldability
107 comments
Read more

MAN B&W MC Engine VIT Pump

The pump is basically a jerk type with a plunger moving in a matched barrel, using two helical grooves machined in the plunger to control the end of injection by uncovering spill ports and causing the discharge pressure to drop rapidly, thus causing the needle valve in the injector to close. Oil is supplied to the barrel via the spill ports and a suction valve. The suction valve, situated at the top of the barrel opens when the pressure in the  barrel falls below the supply pump pressure; i.e. during downward stroke of plunger, while spill ports are covered by plunger. Replaceable erosion plugs  are fitted in the pump housing opposite the spill ports. The high pressure oil, spilling back, as the edge of the helix uncovers the s...
Post a Comment
Read more

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation...
9 comments
Read more