Skip to main content

Lost motion

On a two stroke engine, the fuel pumps must be retimed when the engine is required to reverse direction (i.e. run astern). This is done by moving the fuel pump cams or fuel pump cam follower positions relative to the crankshaft.

If one cylinder of the engine is considered (left), the piston is just before TDC with the engine running ahead and the crankshaft rotating clockwise. The piston is moving up towards TDC. The picture on the right shows the fuel cam at this point; where the cam follower is rising up the lift of the cam as it rotates clockwise. This point can be considered as the start of injection.

If, at this point the engine is stopped, and is started in the reverse direction (astern), the crankshaft now moves in an anticlockwise direction. Then the piston in this particular unit is now moving down the cylinder and is just after TDC. At this point fuel injection should have just finished. However, by studying the picture of the cam (right) it can be seen that the camshaft has reversed direction (because it is directly driven from the crankshaft), and is also rotating anticlockwise.

 Because the engine is started using compressed air admitted through the air start valves, the operating mechanism for these must also be retimed.
Labels:

Comments

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Manganese bronze is not typically used as a propeller material .Why

1. High cost: Manganese bronze is a costly alloy, making it less economical for large propellers. 2. Low strength-to-weight ratio: Compared to other propeller materials like nickel-aluminum bronze or stainless steel, manganese bronze has a lower strength-to-weight ratio. 3. Susceptible to corrosion: Manganese bronze can corrode in seawater, especially when exposed to high velocities and turbulence. 4. Poor cavitation resistance: Manganese bronze is more prone to cavitation damage than other materials. 5. Difficult to cast and machine: Manganese bronze is challenging to cast and machine, making it less desirable for complex propeller geometries. 6. Limited weldability: Manganese bronze has poor weldability, making repairs and modifications difficult. Nickel-aluminum bronze or stainless steel are commonly used for propellers due to their: - High strength and durability - Excellent corrosion resistance - Good cavitation resistance - Ease of casting and machining - Weldability
107 comments
Read more

MAN B&W MC Engine VIT Pump

The pump is basically a jerk type with a plunger moving in a matched barrel, using two helical grooves machined in the plunger to control the end of injection by uncovering spill ports and causing the discharge pressure to drop rapidly, thus causing the needle valve in the injector to close. Oil is supplied to the barrel via the spill ports and a suction valve. The suction valve, situated at the top of the barrel opens when the pressure in the  barrel falls below the supply pump pressure; i.e. during downward stroke of plunger, while spill ports are covered by plunger. Replaceable erosion plugs  are fitted in the pump housing opposite the spill ports. The high pressure oil, spilling back, as the edge of the helix uncovers the s...
Post a Comment
Read more

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation...
9 comments
Read more