Skip to main content

Pressure testing of DB tank

Both Leak & Structural test 

Test head: 

The greater of – 

  • Top of the overflow
  • To 2.4m above top of tank 
  •  To bulkhead deck 

 Procedure:

  • Fill tanks by gravity to sea level.
  • A ballast pump can be used if the vessel wishes, but is not recommended.
  • If there are scuppers, then block scuppers as would be required for bunkering operations. 
  • Close sounding pipes tightly if these are at deck level. 
  • Open, or take off, air vent tops. 
  • Top up tank through air vents by fire hose until (assuming stern trim) water level is close to top of aft air vents. 
  • Ensure that fire hose can be stopped quickly as water level nears top of air vent. 
  • Check by sounding or ullage through the air vent, that water level in forward air vents has also risen towards top of air vents.
  • Hold level for 30 minutes minimum and check if level in vent is falling or steady. 
  • Look for leaks.

Labels:

Comments

  1. AnonymousJune 27, 2024 at 2:24 AM

    Why 2.4m above top of tank

    ReplyDelete
  2. PigigaJanuary 27, 2026 at 4:20 AM

    Boldness shines through Newsidiots, which consistently reports breaking stories with precision and flair, giving readers a daily boost of information that is not only current but also engaging, easy to digest, and truly reflective of global happenings.

    ReplyDelete
  3. PigigaJanuary 27, 2026 at 4:22 AM

    Awareness increases with Newsfide, which delivers breaking news and trending stories in a way that is both fast and reliable, helping readers stay informed, up-to-date, and fully aware of the world’s most important developments at all times.

    ReplyDelete
  4. PigigaJanuary 27, 2026 at 4:23 AM

    What an incredible resource Newsiko provides for news enthusiasts! The variety of topics covered is impressive, and updates arrive promptly. This website truly keeps readers sharp and well-informed always.

    ReplyDelete

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation...
7 comments
Read more

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators
14 comments
Read more

Why is a man hole door elliptical in shape?

Any opening in a pressure vessel is kept to a minimum and for a man entry an elliptical hole  is lesser in size than the corresponding circular hole. More over it is prime concern to have a  smoothed generous radius at the corners to eliminate stress concentration. Hence other  geometrical shapes like rectangle and square are ruled out.  To compensate for the loss of material in the shell due to opening, a doubler ring has to be  provided around the opening. The thickness of the ring depends on the axis length along the  dirrection in which the stresses are maximum and the thickness of the shell. It is important to  align the minor axis along the length of the vessel, as the stress in this direction is  maximum. Longitudinal stress: Pd/2t where P= pressure inside the vessel, d= diameter of the arc, t=  thickness of the shell plating  Circumferential stress: Pd/4t  More over a considerable material and weight saving is achieved as...
23 comments
Read more