Skip to main content

Air Compressor requirements

  • Two starting compressors must be fitted, of sufficient total capacity to meet the engine requirements. Each compressor must be able to press up Air receiver from 15 bar to 25 bar in thirty minutes. Two air receivers must to be provided. Total air receiver capacity is to be sufficient for Twelve (12) starts of Reversible engines and six (6) starts for non-reversible engines.
  • Additional one Diesel driven or hand operated (or if possible, both) emergency air compressor must be fitted to start auxiliary engines of a “Dead Ship”.
  • Safety valves or preferably bursting discs must be fitted on the cooling water casing to give ample relief of pressure, should an air-cooling tube burst.
  • Each compressor must have a safety valve designed so that the accumulated pressure, with the outlet valve closed will not exceed 10% of the maximum working pressure.
  • The air compressor cylinders, covers, intercoolers and after-coolers, are tested by hydraulic pressure to twice their working pressure.
  • The casing of the inter-cooler and after-cooler is hydraulically tested to 1.5 times cooling water pressure. Thus, for 4 bar cooling water pressure, the casing will be tested at 6 bar pressure.
  • A water separator or drain should be fitted on the airside of each intercooler. The drain cock should be used at regular intervals to prevent water from one stage being carried into the following stage.
Labels:

Comments

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation...
8 comments
Read more

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators
15 comments
Read more

Manganese bronze is not typically used as a propeller material .Why

1. High cost: Manganese bronze is a costly alloy, making it less economical for large propellers. 2. Low strength-to-weight ratio: Compared to other propeller materials like nickel-aluminum bronze or stainless steel, manganese bronze has a lower strength-to-weight ratio. 3. Susceptible to corrosion: Manganese bronze can corrode in seawater, especially when exposed to high velocities and turbulence. 4. Poor cavitation resistance: Manganese bronze is more prone to cavitation damage than other materials. 5. Difficult to cast and machine: Manganese bronze is challenging to cast and machine, making it less desirable for complex propeller geometries. 6. Limited weldability: Manganese bronze has poor weldability, making repairs and modifications difficult. Nickel-aluminum bronze or stainless steel are commonly used for propellers due to their: - High strength and durability - Excellent corrosion resistance - Good cavitation resistance - Ease of casting and machining - Weldability
88 comments
Read more